Table of Contents
get bss and set bss commands
This chapter describes commands that can be used to view and set Basic Service Set of radio information.
This chapter describes commands that can be used to view and set Basic Service Set of radio information.
10.1 get bss
Summary of get bss commands:
Command | Description | |
---|---|---|
All, wlan0bssvap0, wlan0bssvap1, wlan0bssvap2, wlan0bssvap3, wlan0bssvap4, wlan0bssvap5, wlan0bssvap6, wlan0bssvap7, wlan0bssvap8, wlan0bssvap9, wlan0bssvap10, wlan0bssvap11, wlan0bssvap12, wlan0bssvap13, wlan0bssvap14, wlan0bssvap15, wlan1bssvap0, wlan1bssvap1, wlan1bssvap2, wlan1bssvap3, wlan1bssvap4, wlan1bssvap5, wlan1bssvap6, wlan1bssvap7, wlan1bssvap8, wlan1bssvap9, wlan1bssvap10, wlan1bssvap11, wlan1bssvap12, wlan1bssvap13, wlan1bssvap14, wlan1bssvap15
|
beacon-interface | Display Service set interface used for beacons |
broadcast-key-refresh-rate | Display the 802.1x broadcastkey refresh rate command specifying the interval after which the broadcast keys are changed | |
description | Display the description | |
detail | * Get all properties * | |
global-radius | Display whether global radius server settings are used | |
ignore-broadcast-ssid | Display the indicator to not send SSID in beacons and ignore probe requests | |
mac | Display the MAC address | |
name | Display the the name of the instance only | |
radio | Display the Radio this BSS is part of | |
radius-accounting | Display whether RADIUS accounting is enabled | |
radius-backupone-ip | Display the Backup one RADIUS server IP address | |
radius-backupone-ipv6 | Display the Backup one RADIUS server IPv6 address | |
radius-backupthree-ip | Display the Backup three RADIUS server IP address | |
radius-backupthree-ipv6 | Display the Backup three RADIUS server IPv6 address | |
radius-backuptwo-ip | Display the Backup two RADIUS server IP address | |
radius-backuptwo-ipv6 | Display the Backup two RADIUS server IPv6 address | |
radius-current | Display the Current Active RADIUS Serevr | |
radius-ip | Display the Primary RADIUS server IP address | |
radius-ip-network | Display the RADIUS server IP network | |
radius-ipv6 | Display the RADIUS server IPv6 address | |
rsn-preauthentication | Display whether RSN pre-authentication is allowed | |
session-key-refresh-rate | Display the 802.1x session-key-refresh-rate object specifying the interval after which unicast session keys are changed | |
shared-key-authentication | Display whether Shared Key authentication is permitted | |
vlan-tagged-interface | Display that Dynamic VLANs are added on this interface | |
wpa-allowed | Display whether WPA is allowed | |
wpa-cipher-ccmp | Display whether CCMP is permitted as a WPA cipher | |
wpa-cipher-tkip | Display whether TKIP is permitted as a WPA cipher | |
wpa2-allowed | Display whether WPA2 is allowed |
10.1.1 get bss beacon-interface
Function: Display service set interface used for beacons.
Command: get bss beacon-interface
Example:
Command: get bss beacon-interface
Example:
ARC2000MAP# get bss wlan0bssvap0 beacon-interface wlan0
10.1.2 get bss broadcast-key-refresh-rate
Function: Display the 802.1x broadcastkey refresh rate command specifying the interval after which the broadcast keys are changed.
Command: get bss broadcast-key-refresh-rate
Example:
Command: get bss broadcast-key-refresh-rate
Example:
ARC2000MAP# get bss wlan0bssvap0 broadcast-key-refresh-rate 86400
10.1.3 get bss description
Function: Display the description.
Command: get bss description
Example:
Command: get bss description
Example:
ARC2000MAP# get bss wlan0bssvap0 description Virtual Access Point 0
10.1.4 get bss detail
Function: Display all details.
Command: get bss detail
Example:
Command: get bss detail
Example:
ARC2000MAP# get bss wlan0bssvap0 detail Property Value -------------------------------------------------- status up description Virtual Access Point 0 radio wlan0 beacon-interface wlan0 mac F8:F7:D3:00:26:10 ignore-broadcast-ssid off global-radius on radius-accounting off radius-ip 192.168.1.1 radius-backupone-ip radius-backuptwo-ip radius-backupthree-ip radius-current radius-ip-network ipv4 vlan-tagged-interface brvlan1 shared-key-authentication off wpa-cipher-tkip on wpa-cipher-ccmp on wpa-allowed on wpa2-allowed on rsn-preauthentication off broadcast-key-refresh-rate 86400 session-key-refresh-rate 0 radius-ipv6 radius-backupone-ipv6 radius-backuptwo-ipv6 radius-backupthree-ipv6
10.1.5 get bss global-radius
Function: Display whether global radius server settings are used.
Command: get bss global-radius
Example:
Command: get bss global-radius
Example:
ARC2000MAP# get bss wlan0bssvap0 global-radius on
10.1.6 get bss ignore-broadcast-ssid
Function: Display the indicator to not send SSID in beacons and ignore probe requests.
Command: get bss ignore-broadcast-ssid
Example:
Command: get bss ignore-broadcast-ssid
Example:
ARC2000MAP# get bss wlan0bssvap0 ignore-broadcast-ssid off
10.1.7 get bss mac
Function: Display the MAC address.
Command: get bss mac
Example:
Command: get bss mac
Example:
ARC2000MAP# get bss wlan0bssvap0 mac F8:F7:D3:00:03:80
10.1.8 get bss name
Function: Display the name of the instance only.
Command: get bss name
Example:
Command: get bss name
Example:
ARC2000MAP# get bss wlan0bssvap0 name wlan0bssvap0
10.1.9 get bss radio
Function: Display the radio this BSS is part of.
Command: get bss radio
Example:
Command: get bss radio
Example:
ARC2000MAP# get bss wlan0bssvap0 radio wlan0
10.1.10 get bss radius-accounting
Function: Display whether RADIUS accounting is enabled.
Command: get bss radius-accounting
Example:
Command: get bss radius-accounting
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-accounting off
10.1.11 get bss radius-backupone-ip
Function: Display the backup one RADIUS server IP address.
Command: get bss radius-backupone-ip
Example:
Command: get bss radius-backupone-ip
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backupone-ip
10.1.12 get bss radius-backupone-ipv6
Function: Display the backup one RADIUS server IPv6 address.
Command: get bss radius-backupone-ipv6
Example:
Command: get bss radius-backupone-ipv6
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backupone-ipv6
10.1.13 get bss radius-backupthree-ip
Function: Display the backup three RADIUS server IP address.
Command: get bss radius-backupthree-ip
Example:
Command: get bss radius-backupthree-ip
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backupthree-ip
10.1.14 get bss radius-backupthree-ipv6
Function: Display the backup three RADIUS server IPv6 address.
Command: get bss radius-backupthree-ipv6
Example:
Command: get bss radius-backupthree-ipv6
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backupthree-ipv6
10.1.15 get bss radius-backuptwo-ip
Function: Display the backup two RADIUS server IP address.
Command: get bss radius-backuptwo-ip
Example:
Command: get bss radius-backuptwo-ip
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backuptwo-ip
10.1.16 get bss radius-backuptwo-ipv6
Function: Display the backup two RADIUS server IPv6 address.
Command: get bss radius-backuptwo-ipv6
Example:
Command: get bss radius-backuptwo-ipv6
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-backuptwo-ipv6
10.1.17 get bss radius-current
Function: Display the current Active RADIUS Server.
Command: get bss radius-current
Example:
Command: get bss radius-current
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-current
10.1.18 get bss radius-ip
Function: Display the primary RADIUS server IP address.
Command: get bss radius-ip
Example:
Command: get bss radius-ip
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-ip 192.168.1.1
10.1.19 get bss radius-ip-network
Function: Display the RADIUS server IP network.
Command: get bss radius-ip-network
Example:
Command: get bss radius-ip-network
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-ip-network ipv4
10.1.20 get bss radius-ipv6
Function: Display the RADIUS server IPv6 address.
Command: get bss radius-ipv6
Example:
Command: get bss radius-ipv6
Example:
ARC2000MAP# get bss wlan0bssvap0 radius-ipv6
10.1.21 get bss rsn-preauthentication
Function: Display whether RSN pre-authentication is allowed.
Command: get bss rsn-preauthentication
Example:
Command: get bss rsn-preauthentication
Example:
ARC2000MAP# get bss wlan0bssvap0 rsn-preauthentication off
10.1.22 get bss session-key-refresh-rate
Function: Display the 802.1x session-key-refresh-rate object specifying the interval after which unicast session keys are changed.
Command: get bss session-key-refresh-rate
Example:
Command: get bss session-key-refresh-rate
Example:
ARC2000MAP# get bss wlan0bssvap0 session-key-refresh-rate 0
10.1.23 get bss shared-key-authentication
Function: Display whether Shared Key authentication is permitted.
Command: get bss shared-key-authentication
Example:
Command: get bss shared-key-authentication
Example:
ARC2000MAP# get bss wlan0bssvap0 shared-key-authentication off
10.1.24 get bss vlan-tagged-interface
Function: Display that dynamic VLANs are added on this interface.
Command: get bss vlan-tagged-interface
Example:
Command: get bss vlan-tagged-interface
Example:
ARC2000MAP# get bss wlan0bssvap0 vlan-tagged-interface brvlan1
10.1.25 get bss wpa-allowed
Function: Display whether WPA is allowed.
Command: get bss wpa-allowed
Example:
Command: get bss wpa-allowed
Example:
ARC2000MAP# get bss wlan0bssvap0 wpa-allowed on
10.1.26 get bss wpa-cipher-ccmp
Function: Display whether CCMP is permitted as a WPA cipher.
Command: get bss wpa-cipher-ccmp
Example:
Command: get bss wpa-cipher-ccmp
Example:
ARC2000MAP# get bss wlan0bssvap0 wpa-cipher-ccmp on
10.1.27 get bss wpa-cipher-tkip
Function: Display whether TKIP is permitted as a WPA cipher.
Command: get bss wpa-cipher-tkip
Example:
Command: get bss wpa-cipher-tkip
Example:
ARC2000MAP# get bss wlan0bssvap0 wpa-cipher-tkip on
10.1.28 get bss wpa2-allowed
Function: Display whether WPA2 is allowed.
Command: get bss wpa2-allowed
Example:
Command: get bss wpa2-allowed
Example:
ARC2000MAP# get bss wlan0bssvap0 wpa2-allowed on
10.2 set bss commands
Summary of set bss commands:
Command | Description | |
---|---|---|
All, wlan0bssvap0, wlan0bssvap1, wlan0bssvap2, wlan0bssvap3, wlan0bssvap4, wlan0bssvap5, wlan0bssvap6, wlan0bssvap7, wlan0bssvap8, wlan0bssvap9, wlan0bssvap10, wlan0bssvap11, wlan0bssvap12, wlan0bssvap13, wlan0bssvap14, wlan0bssvap15, wlan1bssvap0, wlan1bssvap1, wlan1bssvap2, wlan1bssvap3, wlan1bssvap4, wlan1bssvap5, wlan1bssvap6, wlan1bssvap7, wlan1bssvap8, wlan1bssvap9, wlan1bssvap10, wlan1bssvap11, wlan1bssvap12, wlan1bssvap13, wlan1bssvap14, wlan1bssvap15
|
beacon-interface | Set the Service set interface used for beacons |
broadcast-key-refresh-rate | Set the 802.1x broadcastkey refresh rate command specifying the interval after which the broadcast keys are changed | |
description | Set the description | |
global-radius | Set whether global radius server settings are used | |
ignore-broadcast-ssid | Set the indicator to not send SSID in beacons and ignore probe requests | |
radio | Set the Radio this BSS is part of | |
radius-accounting | Set whether RADIUS accounting is enabled | |
radius-backupone-ip | Set the Backup one RADIUS server IP address | |
radius-backupone-key | Set the Key for communication with backup one RADIUS server | |
radius-backupthree-ip | Set the Backup three RADIUS server IP address | |
radius-backupthree-key | Set the Key for communication with backup three RADIUS server | |
radius-backuptwo-ip | Set the Backup two RADIUS server IP address | |
radius-backuptwo-key | Set the Key for communication with backup two RADIUS server | |
radius-current | Set the Current Active RADIUS Serevr | |
radius-ip | Set the Primary RADIUS server IP address | |
radius-ip-network | Set the RADIUS server IP network | |
radius-key | Set the Key for communication with Primary RADIUS server | |
rsn-preauthentication | Set whether RSN pre-authentication is allowed | |
session-key-refresh-rate | Set the 802.1x session-key-refresh-rate object specifying the interval after which unicast session keys are changed | |
shared-key-authentication | Set whether Shared Key authentication is permitted | |
vlan-tagged-interface | Set the Dynamic VLANs are added on this interface | |
wpa-allowed | Set whether WPA is allowed | |
wpa-cipher-ccmp | Set whether CCMP is permitted as a WPA cipher | |
wpa-cipher-tkip | Set whether TKIP is permitted as a WPA cipher | |
wpa2-allowed | Set whether WPA2 is allowed |
10.2.1 set bss beacon-interface
Function: Set the service set interface used for beacons. The valid value is the name of an existing interface instance with type of service-set.
Command: set bss beacon-interface
Example:
Command: set bss beacon-interface
Example:
ARC2000MAP# set bss wlan0bssvap0 beacon-interface wlan0
10.2.2 set bss broadcast-key-refresh-rate
Function: Set the 802.1x broadcastkey refresh rate command specifying the interval after which the broadcast keys are changed. Valid values: [0,86400].
Command: set bss broadcast-key-refresh-rate
Example:
Command: set bss broadcast-key-refresh-rate
Example:
ARC2000MAP# set bss wlan0bssvap0 broadcast-key-refresh-rate 86400
10.2.3 set bss description
Function: Set the description. The valid value is an ASCII string.
Command: set bss description
Example:
Command: set bss description
Example:
ARC2000MAP# set bss wlan0bssvap0 description ?Virtual Access Point 0?
10.2.4 set bss global-radius
Function: Set whether global radius server settings are used. Valid values: ?on? or ?off?.
Command: set bss global-radius
Example:
Command: set bss global-radius
Example:
ARC2000MAP# set bss wlan0bssvap0 global-radius on
10.2.5 set bss ignore-broadcast-ssid
Function: Set the indicator to not send SSID in beacons and ignore probe requests. Valid values: ?on? or ?off?.
Command: set bss ignore-broadcast-ssid
Example:
Command: set bss ignore-broadcast-ssid
Example:
ARC2000MAP# set bss wlan0bssvap0 ignore-broadcast-ssid off
10.2.6 set bss radio
Function: Set the radio that this BSS is part of. The valid value is the name of an existing radio instance.
Command: set bss radio
Example:
Command: set bss radio
Example:
ARC2000MAP# set bss wlan0bssvap0 radio wlan0
10.2.7 set bss radius-accounting
Function: Set whether RADIUS accounting is enabled. Valid values: ?on? or ?off?.
Command: set bss radius-accounting
Example:
Command: set bss radius-accounting
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-accounting off
10.2.8 set bss radius-backupone-ip
Function: Set the backup one RADIUS server IP address. Valid value: an IP address.
Command: set bss radius-backupone-ip
Example:
Command: set bss radius-backupone-ip
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backupone-ip 10.1.1.1
10.2.9 set bss radius-backupone-key
Function: Set the key for communication with backup one RADIUS server. Valid value: a string.
Command: set bss radius-backupone-key
Example:
Command: set bss radius-backupone-key
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backupone-key aaa
10.2.10 set bss radius-backuptwo-ip
Function: Set the backup two RADIUS server IP address. Valid value: an IP address.
Command: set bss radius-backuptwo-ip
Example:
Command: set bss radius-backuptwo-ip
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backuptwo-ip 20.1.1.1
10.2.11 set bss radius-backuptwo-key
Function: Set the key for communication with backup two RADIUS server. Valid value: a string.
Command: set bss radius-backuptwo-key
Example:
Command: set bss radius-backuptwo-key
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backuptwo-key bbb
10.2.12 set bss radius-backupthree-ip
Function: Set the backup three RADIUS server IP address. Valid value: an IP address.
Command: set bss radius-backupthree-ip
Example:
Command: set bss radius-backupthree-ip
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backupthree-ip 30.1.1.1
10.2.13 set bss radius-backupthree-key
Function: Set the key for communication with backup three RADIUS server. Valid value: a string.
Command: set bss radius-backupthree-key
Example:
Command: set bss radius-backupthree-key
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-backupthree-key ccc
10.2.14 set bss radius-current
Function: Set the current Active RADIUS Server. Valid values: ?primary???backupone???backuptwo???backupthree?.
Command: set bss radius-current
Example:
Command: set bss radius-current
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-current primary
10.2.15 set bss radius-ip
Function: Set the primary RADIUS server IP address. Valid value: an IP address.
Command: set bss radius-ip
Example:
Command: set bss radius-ip
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-ip 192.168.1.1
10.2.16 set bss radius-ip-network
Function: Set the RADIUS server IP network. Valid values: ?ipv4??ipv6?.
Command: set bss radius-ip-network
Example:
Command: set bss radius-ip-network
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-ip-network ipv4
10.2.17 set bss radius-key
Function: Set the key for communication with the Primary RADIUS server. Valid value: a string.
Command: set bss radius-key
Example:
Command: set bss radius-key
Example:
ARC2000MAP# set bss wlan0bssvap0 radius-key test
10.2.18 set bss rsn-preauthentication
Function: Set whether RSN pre-authentication is allowed. Valid values: ?on?,?off?.
Command: set bss rsn-preauthentication
Example:
Command: set bss rsn-preauthentication
Example:
ARC2000MAP# set bss wlan0bssvap0 rsn-preauthentication off
10.2.19 set bss session-key-refresh-rate
Function: Set the 802.1x session-key-refresh-rate object specifying the interval after which unicast session keys are changed. Valid value: 0, [30,86400].
Command: set bss session-key-refresh-rate
Example:
Command: set bss session-key-refresh-rate
Example:
ARC2000MAP# set bss wlan0bssvap0 session-key-refresh-rate 0
10.2.20 set bss shared-key-authentication
Function: Set whether Shared Key authentication is permitted. Valid values: ?on?,?off?.
Command: set bss shared-key-authentication
Example:
Command: set bss shared-key-authentication
Example:
ARC2000MAP# set bss wlan0bssvap0 shared-key-authentication off
10.2.21 set bss vlan-tagged-interface
Function: Set whether dynamic VLANs are added on this interface. Valid value: the name of an existing interface.
Command: set bss vlan-tagged-interface
Example:
Command: set bss vlan-tagged-interface
Example:
ARC2000MAP# set bss wlan0bssvap0 vlan-tagged-interface brvlan1
10.2.22 set bss wpa-allowed
Function: Set whether WPA is allowed. Valid value: ?on? or ?off?.
Command: set bss wpa-allowed
Example:
Command: set bss wpa-allowed
Example:
ARC2000MAP# set bss wlan0bssvap0 wpa-allowed on
10.2.23 set bss wpa-cipher-ccmp
Function: Set whether CCMP is permitted as a WPA cipher. Valid value: ?on? or ?off?.
Command: set bss wpa-cipher-ccmp
Example:
Command: set bss wpa-cipher-ccmp
Example:
ARC2000MAP# set bss wlan0bssvap0 wpa-cipher-ccmp on
10.2.24 set bss wpa-cipher-tkip
Function: Set whether TKIP is permitted as a WPA cipher. Valid value: ?on? or ?off?.
Command: set bss wpa-cipher-tkip
Example:
Command: set bss wpa-cipher-tkip
Example:
ARC2000MAP# set bss wlan0bssvap0 wpa-cipher-tkip on
10.2.25 set bss wpa2-allowed
Function: Set whether WPA2 is allowed. Valid value: ?on? or ?off?.
Command: set bss wpa2-allowed
Example:
Command: set bss wpa2-allowed
Example:
ARC2000MAP# set bss wlan0bssvap0 wpa2-allowed on
Return to AP Wireless CLI Table of Contents