13. Managed AP Commands

Table of Contents

get managed-ap and set managed-ap commands
This chapter describes commands that can be used to view and set managed-ap information.

13.1 get managed-ap

Summary of get managed-ap commands:

Command Description
cfg-ip-base-port Display the Config Base IP port (1-65000)
detail * Get all properties *
dhcp-ip-base-port Display the DHCP Base IP port
dhcp-switch-address-1 Display the DHCP Switch IP Address 1
dhcp-switch-address-2 Display the DHCP Switch IP Address 2
dhcp-switch-address-3 Display the DHCP Switch IP Address 3
dhcp-switch-address-4 Display the DHCP Switch IP Address 4
dhcpv6-switch-ipv6-address-1 Display the DHCPv6 Switch IPv6 Address 1
dhcpv6-switch-ipv6-address-2 Display the DHCPv6 Switch IPv6 Address 2
dhcpv6-switch-ipv6-address-3 Display the DHCPv6 Switch IPv6 Address 3
dhcpv6-switch-ipv6-address-4 Display the DHCPv6 Switch IPv6 Address 4
dns-switch-address-1 Display the DNS Switch IP Address 1
dns-switch-address-2 Display the DNS Switch IP Address 2
dns-switch-address-3 Display the DNS Switch IP Address 3
dns-switch-address-4 Display the DNS Switch IP Address 4
ip-base-port Display the Base IP port
managed-mode-watchdog Display the Minutes before reset (0-1440)
managed-type Display the Type (0-mapd,1-capwap)
mode Display the Mode
switch-address-1 Display the Switch IP Address 1
switch-address-2 Display the Switch IP Address 2
switch-address-3 Display the Switch IP Address 3
switch-address-4 Display the Switch IP Address 4
switch-ipv6-address-1 Display the Switch IPV6 Address 1
switch-ipv6-address-2 Display the Switch IPV6 Address 2
switch-ipv6-address-3 Display the Switch IPV6 Address 3
switch-ipv6-address-4 Display the Switch IPV6 Address 4

13.1.1 get managed-ap cfg-ip-base-port

Function: Display the config Base IP port (1-65000).
Command: get managed-ap cfg-ip-base-port
Example:

ARC2000MAP# get managed-ap cfg-ip-base-port
57775

13.1.2 get managed-ap detail

Function: Display all properties.
Command: get managed-ap detail
Example:

ARC2000MAP# get managed-ap detail
Property                      Value
------------------------------------------
mode                          up
managed-type                  1
ap-state                      up
switch-address-1              10.1.1.1
switch-address-2              10.1.1.2
switch-address-3              10.1.1.3
switch-address-4              10.1.1.4
switch-ipv6-address-1         2010::1
switch-ipv6-address-2         2010::2
switch-ipv6-address-3         2010::3
switch-ipv6-address-4         2010::4
dhcp-switch-address-1         20.1.1.1
dhcp-switch-address-2         20.1.1.2
dhcp-switch-address-3         20.1.1.3
dhcp-switch-address-4         20.1.1.4
dns-switch-address-1          202.106.11.1
dns-switch-address-2          202.106.11.2
dns-switch-address-3          202.106.11.3
dns-switch-address-4          202.106.11.4
managed-mode-watchdog         0
dhcp-ip-base-port
cfg-ip-base-port              57775
ip-base-port                  57775
dhcpv6-switch-ipv6-address-1  2011::1
dhcpv6-switch-ipv6-address-2  2011::2
dhcpv6-switch-ipv6-address-3  2011::3
dhcpv6-switch-ipv6-address-4  2011::4

13.1.3 get managed-ap dhcp-ip-base-port

Function: Display the DHCP base IP port.
Command: get managed-ap dhcp-ip-base-port
Example:

ARC2000MAP# get managed-ap dhcp-ip-base-port

13.1.4 get managed-ap dhcp-switch-address-1

Function: Display the DHCP switch IP address 1.
Command: get managed-ap dhcp-switch-address-1
Example:

ARC2000MAP# get managed-ap dhcp-switch-address-1
20.1.1.1

13.1.5 get managed-ap dhcp-switch-address-2

Function: Display the DHCP switch IP address 2.
Command: get managed-ap dhcp-switch-address-2
Example:

ARC2000MAP# get managed-ap dhcp-switch-address-2
20.1.1.2

13.1.6 get managed-ap dhcp-switch-address-3

Function: Display the DHCP switch IP address 3.
Command: get managed-ap dhcp-switch-address-3
Example:

ARC2000MAP# get managed-ap dhcp-switch-address-3
20.1.1.3

13.1.7 get managed-ap dhcp-switch-address-4

Function: Display the DHCP switch IP address 4.
Command: get managed-ap dhcp-switch-address-4
Example:

ARC2000MAP# get managed-ap dhcp-switch-address-4
20.1.1.4

13.1.8 get managed-ap dhcpv6-switch-ipv6-address-1

Function: Display the DHCPv6 switch IP address 1.
Command: get managed-ap dhcpv6-switch-ipv6-address-1
Example:

ARC2000MAP# get managed-ap dhcpv6-switch-ipv6-address-1
2011::1

13.1.9 get managed-ap dhcpv6-switch-ipv6-address-2

Function: Display the DHCPv6 switch IP address 2.
Command: get managed-ap dhcpv6-switch-ipv6-address-2
Example:

ARC2000MAP# get managed-ap dhcpv6-switch-ipv6-address-2
2011::2

13.1.10 get managed-ap dhcpv6-switch-ipv6-address-3

Function: Display the DHCPv6 switch IP address 3.
Command: get managed-ap dhcpv6-switch-ipv6-address-3
Example:

ARC2000MAP# get managed-ap dhcpv6-switch-ipv6-address-3
2011::3

13.1.11 get managed-ap dhcpv6-switch-ipv6-address-4

Function: Display the DHCPv6 switch IP address 4.
Command: get managed-ap dhcpv6-switch-ipv6-address-4
Example:

ARC2000MAP# get managed-ap dhcpv6-switch-ipv6-address-4
2011::4

13.1.12 get managed-ap dns-switch-address-1

Function: Display the DNS switch IP address 1.
Command: get managed-ap dns-switch-address-1
Example:

ARC2000MAP# get managed-ap dns-switch-address-1
202.106.11.1

13.1.13 get managed-ap dns-switch-address-2

Function: Display the DNS switch IP address 2.
Command: get managed-ap dns-switch-address-2
Example:

ARC2000MAP# get managed-ap dns-switch-address-2
202.106.11.2

13.1.14 get managed-ap dns-switch-address-3

Function: Display the DNS switch IP address 3.
Command: get managed-ap dns-switch-address-3
Example:

ARC2000MAP# get managed-ap dns-switch-address-3
202.106.11.3

13.1.15 get managed-ap dns-switch-address-4

Function: Display the DNS switch IP address 4.
Command: get managed-ap dns-switch-address-4
Example:

ARC2000MAP# get managed-ap dns-switch-address-4
202.106.11.4

13.1.16 get managed-ap ip-base-port

Function: Display the base IP port.
Command: get managed-ap ip-base-port
Example:

ARC2000MAP# get managed-ap ip-base-port
57775

13.1.17 get managed-ap managed-mode-watchdog

Function: Display the minutes before reset (0-1440).
Command: get managed-ap managed-mode-watchdog
Example:

ARC2000MAP# get managed-ap managed-mode-watchdog
0

13.1.18 get managed-ap managed-type

Function: Display the type (0-mapd,1-capwap).
Command: get managed-ap managed-type
Example:

ARC2000MAP# get managed-ap managed-type
1

13.1.19 get managed-ap mode

Function: Display the mode.
Command: get managed-ap mode
Example:

ARC2000MAP# get managed-ap mode
up

13.1.20 get managed-ap switch-address-1

Function: Display the switch IP address 1.
Command: get managed-ap switch-address-1
Example:

ARC2000MAP# get managed-ap switch-address-1
10.1.1.1

13.1.21 get managed-ap switch-address-2

Function: Display the switch IP address 2.
Command: get managed-ap switch-address-2
Example:

ARC2000MAP# get managed-ap switch-address-2
10.1.1.2

13.1.22 get managed-ap switch-address-3

Function: Display the switch IP address 3.
Command: get managed-ap switch-address-3
Example:

ARC2000MAP# get managed-ap switch-address-3
10.1.1.3

13.1.23 get managed-ap switch-address-4

Function: Display the switch IP address 4.
Command: get managed-ap switch-address-4
Example:

ARC2000MAP# get managed-ap switch-address-4
10.1.1.4

13.1.24 get managed-ap switch-ipv6-address-1

Function: Display the switch IPV6 address 1.
Command: get managed-ap switch-ipv6-address-1
Example:

ARC2000MAP# get managed-ap switch-ipv6-address-1
2010::1

13.1.25 get managed-ap switch-ipv6-address-2

Function: Display the switch IPV6 address 2.
Command: get managed-ap switch-ipv6-address-2
Example:

ARC2000MAP# get managed-ap switch-ipv6-address-2
2010::2

13.1.26 get managed-ap switch-ipv6-address-3

Function: Display the switch IPV6 address 3.
Command: get managed-ap switch-ipv6-address-3
Example:

ARC2000MAP# get managed-ap switch-ipv6-address-3
2010::3

13.1.27 get managed-ap switch-ipv6-address-4

Function: Display the switch IPV6 address 4.
Command: get managed-ap switch-ipv6-address-4
Example:

ARC2000MAP# get managed-ap switch-ipv6-address-4
2010::4

 


13.2 set managed-ap

Summary of set managed-ap commands:

Command Description
managed-mode-watchdog Set the Minutes before reset (0-1440)
managed-type Set the Type(0-mapd,1-capwap)
mode Set the Mode
pass-phrase Set the Switch pass-phrase
switch-address-1 Set the Switch IP Address 1
switch-address-2 Set the Switch IP Address 2
switch-address-3 Set the Switch IP Address 3
switch-address-4 Set the Switch IP Address 4
switch-ipv6-address-1 Set the Switch IPV6 Address 1
switch-ipv6-address-2 Set the Switch IPV6 Address 2
switch-ipv6-address-3 Set the Switch IPV6 Address 3
switch-ipv6-address-4 Set the Switch IPV6 Address 4

13.2.1 set managed-ap managed-mode-watchdog

Function: Set the minutes before reset (0-1440). Valid values: [0,1440], 0 means watchdog is disabled.
Command: set managed-ap managed-mode-watchdog
Example:

ARC2000MAP# set managed-ap managed-mode-watchdog 0

13.2.2 set managed-ap managed-type

Function: Set the type (0-mapd,1-capwap). Valid values: [0,1], 0 means discover with mapd, 1 means discover with capwap.
Command: set managed-ap managed-type
Example:

ARC2000MAP# set managed-ap managed-type 1

13.2.3 set managed-ap mode

Function: Set the mode. Valid values: ?up? or ?down?.
Command: set managed-ap mode
Example:

ARC2000MAP# set managed-ap mode up

13.2.4 set managed-ap pass-phrase

Function: Set the switch pass-phrase. Valid values:
secret code of length between 8 and 63 characters.
Command: set managed-ap pass-phrase
Example:

ARC2000MAP# set managed-ap pass-phrase 12345678

13.2.5 set managed-ap switch-address-1

Function: Set the switch IP Address 1. Valid value: IP address.
Command: set managed-ap switch-address-1
Example:

ARC2000MAP# set managed-ap switch-address-1 10.1.1.1

13.2.6 set managed-ap switch-address-2

Function: Set the switch IP Address 2. Valid value: IP address.
Command: set managed-ap switch-address-2
Example:

ARC2000MAP# set managed-ap switch-address-2 10.1.1.2

13.2.7 set managed-ap switch-address-3

Function: Set the switch IP Address 3. Valid value: IP address.
Command: set managed-ap switch-address-3
Example:

ARC2000MAP# set managed-ap switch-address-3 10.1.1.3

13.2.8 set managed-ap switch-address-4

Function: Set the switch IP Address 4. Valid value: IP address.
Command: set managed-ap switch-address-4
Example:

ARC2000MAP# set managed-ap switch-address-4 10.1.1.4

13.2.9 set managed-ap switch-ipv6-address-1

Function: Set the switch IPV6 Address 1. Valid value: IPv6 address.
Command: set managed-ap switch-ipv6-address-1
Example:

ARC2000MAP# set managed-ap switch-ipv6-address-1 2010::1

13.2.10 set managed-ap switch-ipv6-address-2

Function: Set the switch IPV6 Address 2. Valid value: IPv6 address.
Command: set managed-ap switch-ipv6-address-2
Example:

ARC2000MAP# set managed-ap switch-ipv6-address-2 2010::2

13.2.11 set managed-ap switch-ipv6-address-3

Function: Set the switch IPV6 Address 3. Valid value: IPv6 address.
Command: set managed-ap switch-ipv6-address-3
Example:

ARC2000MAP# set managed-ap switch-ipv6-address-3 2010::3

13.2.12 set managed-ap switch-ipv6-address-4

Function: Set the switch IPV6 Address 4. Valid value: IPv6 address.
Command: set managed-ap switch-ipv6-address-4
Example:

ARC2000MAP# set managed-ap switch-ipv6-address-4 2010::4

 


Return to AP Wireless CLI Table of Contents